Suzuki GSXS1000 Forum

Suzuki GSXS1000 Forum (https://www.gsxs1000.org/forum/)
-   Suzuki GSXS 1000 Troubleshooting (https://www.gsxs1000.org/forum/suzuki-gsxs-1000-troubleshooting/)
-   -   2017 gsx s1000 al8 tps check help (https://www.gsxs1000.org/forum/suzuki-gsxs-1000-troubleshooting/36985-2017-gsx-s1000-al8-tps-check-help.html)

Leegsxs 07-27-2017 02:28 PM

2017 gsx s1000 al8 tps check help
 
OK what am I doing wrong?
Bike warmed up
Ignition on bike not running
2 pins opposite each other in diagnostics plug bridged

I am getting C00 on my dash where the trip normaly is but no line next to C00 to reference where my tps adjustment is?

What have I not done or missed? ... Done a search on the forum but there's no diffinetive Diy or sticky how to.

Thanks in advance

scooby61 07-27-2017 03:22 PM

Your the second person I've seen here with that issue. If you have the coo then your in service mode. Of you don't have the line to the left you may have to set via the multimeter method or have a dealer look at it. I wonder if the newer ecu has removed that feature?

Doddy666 07-27-2017 03:30 PM

I thought it had to be running?? Mine shows the middle when idling and moves to top when I revving to 3-4k

Sent from my SM-G930F using Tapatalk

scooby61 07-27-2017 03:45 PM

Quote:

Originally Posted by Doddy666 (Post 294289)
I thought it had to be running?? Mine shows the middle when idling and moves to top when I revving to 3-4k

Sent from my SM-G930F using Tapatalk

Your supposed to warm the bike up and then shut it off and Che k with ignition on only was my understanding.
It moves up when you turn the throttle.

Leegsxs 07-27-2017 03:54 PM

I've tried it with the engine running aswell and there is no line

Doddy666 07-27-2017 07:32 PM

Quote:

Originally Posted by scooby61 (Post 294313)
Your supposed to warm the bike up and then shut it off and Che k with ignition on only was my understanding.
It moves up when you turn the throttle.

It doesn't matter what it is with it switched off, if its middle while running its middle while off. it is supposed to be middle then blip and should go up. I found this a bit of a pointless method because even when set right it is not within spec, when you use the test harness and multimeter, which is far more accurate. A tiny amount out makes a big difference.

Sent from my SM-G930F using Tapatalk

adrianpeds 07-27-2017 08:06 PM

Another cause of no line in the C00 on dealer mode is if the TPS is out of scope. Loosen the Torx and move the TPS up and down until you see the line. Did you try that?

Sunny 08-06-2017 09:00 AM

Quote:

Originally Posted by adrianpeds (Post 294457)
Another cause of no line in the C00 on dealer mode is if the TPS is out of scope. Loosen the Torx and move the TPS up and down until you see the line. Did you try that?

I also have the C00 but no line on my faL8. Tried moving my tps but no line appears.

Doddy666 08-06-2017 11:09 AM

Tbh the line is pretty meaningless anyway, check the tps using the harness using a multimeter and forget.

Sent from my SM-G930F using Tapatalk

Ralph Sigi 08-06-2017 12:26 PM

mine is middle at idle, goes up at 1500, is that ok?


All times are GMT -4. The time now is 11:56 AM.

Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.

User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.